Two cutter and V notch CTL

Economical two cut a step horizontal shear line

Economical two cut a step horizontal shear line

Detailed

A, CAH (21) - 300 - d type transverse shear line is introduced
1. Double head uncoiler
Coil diameter: 500 mm
The biggest diameter: 1200 mm
Single head weight: 1.5 tons
Open book speed: over feeding synchronous adjustment
Uncoiling machine adopts synchronous stepless speed regulation with feeding, hydraulic tensioning, disc brakes, motor rotation.
2. The feed buffer device
No pit feed buffer, ranging system, position switch, etc.
3. The feeder
Upper and lower feed roller and measuring roller, feed roller drive system adopts Siemens simotion D425 motion control system.
Center positioning, feeder can longitudinal integral translation; Double motor drive, encoder measuring, servo closed-loop control;
Feed roller adopts polyurethane, 0-120 m/min, normal use highest feeding speed 180 m/min;
4. Press section
Mainly contains V 1 set, servo motor drive. V with transverse step function, automatically adjust according to the program.
At short range: along the sheet stock center + 50 mm, step into a series of seven. V punching shear adopts Siemens servo motor drive, high efficiency, low noise.
Knife (die) with life: every grinding is not less than 1 million times
5. The shear section
Mainly by the + 45 ° shears, - 45 ° shears, transverse sliding table, discharging roll, etc. Shear way: using the servo motor driven CAM mechanism to shear work up and down.
Knife (die) with life: every grinding is not less than 1 million times
6. The loading
Unilateral positioning, stepless speed transmission belt, discharging smoothly. Discharging motor adopts Germany ABB motor, Toshiba inverter control.
7. Points machine
Can complete upper and lower two layers of bedding materials respectively, mainly by the fragmentation devices, transmission belt and magnetic material of first class.
8. Unilateral positioning the automatic tuning device wide
Broadly based on unilateral positioning the automatic tuning wide operation mode to adapt to the different width sheet stock transfer.
Adjustable wide organization adopt linear guide, ball screw transmission ways.
Across the wide linkage concentration adjustable width, position indicator display position.
Pneumatic system is 9.
All pneumatic system adopts Taiwan AIRTAC pneumatic control system, the structure is compact, easy to take over, bus connection.
Electric control system of 10.
Electronic control system includes the main electric control cabinet and work station.
2. The main technical parameters of the production line
1. The processing range:
Slice thickness: 0.23 0.35 mm
Wide: 60-320 - mm
Length: 300-1500 - mm
2. This production line used by the coil material requirements:
The width tolerance: + / - 0.1 mm
MAO thorn: 0.03 mm or less
S: of the deviation in one-way within 2000 mm of 0.2 mm or less
3. The precision production line:
The length tolerance: + / - 0.2 mm
Angle tolerance: + / - 0.025 °
MAO thorn: 0.02 mm or less
4. The feeding speed, working feed speed is 2500 mm/s
5. The knives' service life: not less than 1 million times (once every grinding); Hard alloy material
6. The total installed capacity: about 25 kw
7. The total gas consumption: 1 cubic meters per minute
8. The working conditions:
(1) the temperature is not higher than 40 ° C; (2) voltage fluctuation to 380 v + 10%; (3) the frequency of 50 hz
9. With functions of longitudinal step by step
10. Operating direction: right line (from one side of main work station for equipment, feed direction from left to the left).
分享到:
Hits:  UpdateTime:2017-03-28 16:36:55